Hi there Folks! Hope you are all well especially with all the sadness in the world just now.
Another month gone and another challenge from Claritystamp Ltd.
This month the theme is:
I am so looking forward to seeing all your wonderful entries and just to give you a bit of inspiration, here is my Design Team Sample.....hope you like it xx
Groovi Plates used for first stage
I began with colouring a piece of A5 white Parchment using the Dorso technique.
I applied the Dorso Crayon to the parchment and then applied a touch of Dorso Oil to a piece of Kitchen Roll. Then I applied this to the parchment in a circular motion, blending the colour until even. The picture on the left is my first application. The picture on the right is my second.
I then attached the parchment to my Groovi Plate Mate using the Baby Inset Adapter Plate and the Baby Nested Square Plate. I embossed the Outer Square.
I removed the Baby Inset and replaced it with the larger Groovi Nested Square and embossed the 9th Square, counting from the middle. This gave me a neat frame with slightly smaller border.
I then re-inserted the Baby Inset Adapter, this time I used the Baby 'New Arrival' Plate and added the sentiment to the top and bottom of the square leaving room for my embellishment which you can see comes from the same plate. (more on that later)
For the next stage I worked on the new Groovi Border Plate Mate
Using the Lacy Corner Border (sadly it is omitted from the picture....ooops!) and the Lacy Border Plate, taking elements from these Border plates I built up my design, making sure that the design was even all around the outside and inside of the frame.
Then it was time for a bit of white work, tumble dryer sheet, embossing tools. Nice gentle strokes to gently stretch the parchment and to build up the white work evenly. Go around all the areas to be embossed once, before going around again...giving your work a chance to rest.
Note: always use the size of embossing tool that fits into the area to be embossed......no use using a 6mm ball tool if the area only takes a 1.5mm tool!
This is where I got carried away with the design and went straight to the piercing and Cutting.... without taking photos.....
I attached the white parchment to the Groovi Plate Mate, this time with the Straight Piercing Grid
Using the 1 needle and 2 needle tools I pierced the area between the Frame and Border design.....
forgetting that I wanted to colour the Frame......You can see from the finished pic that I rectified this later......not to be advised once pierced unless you have a steady hand as you do not want the colour to go into the holes or onto your picot edges!!
I used a 2 needle fine Pergamano tool to pierce around the lacy framework and then cut a picot edge using Pergamano Parchment Scissors.......yes it did take a little while.....I was more worried about the edges catching on my clothes......don't wear wool garments when cutting.....or make sure your sleeves are rolled up good and proper......saves the air from going blue.....yes I did have to walk from my craft room to my husband and ask him to very carefully detach me from my work.....and yes after over ten years of parching, I Should Know Better!!
Next step cutting and mounting the two pieces together.
I applied Red Double Sided Tape to the back of the Blue Parchment and also the Front. I attached it to my backing paper. I then removed the cover of the tape on the front and carefully attached the Lacy White Parchment.....best to match up the corners first. I then used my Perfect Layers Ruler to cut the backing paper. This was then attached to a White Card with Red Tape again. I applied some Silver Iridescent Peel-offs around the edge of the blue backing paper and mitred the corners for a better finish!
Now about that Rattle!
You can see that is taken from the Baby Plate along with the Bow.
What you didn't know was that.....it actually rattles!!
I cut the Rattles out with my parchment scissors, piercing and cutting the inside of the handle and around the bow. I used Perga Glue to attach the handles and halfway up the circle (to the blue band) together. I then added some Micro Beads (those beads that are used for nail art are very cheap and are the perfect size for something this small). I then finished glueing the rattles together. It didn't take too long to dry. Next I used Perga Glue to attach the Bow and then attached the rattle to the center of the card using a clear double sided pad.
Hey just a thought.....I will be giving the baby his first Rattle lol!
Now to be honest with you all, this card is not finished yet.....why?
I have added a Satin Insert to the card, just ready to be written on, and now I am awaiting the birth of the baby (not long now) so that I can add his name and the date and time to the tags and add it to the card!
My First Grandchild!
(Tags Border Plate and Scrap Parchment, Scrap backing paper. I will emboss lettering from the new Universal Framer before piercing all around and giving them a picot edge)
So there will be a bit more fussy cutting from me to come, just as well that I love it!
So now it is up to you to get your thinking caps on and to help you, why not pop on over to the Claritystamp Challenge Blog and have a look at what the other Design Team Members have on show.
If you click on their names you will be taken to their blogs to see how they have made their designs.
Wishing you all good luck in the challenge, the Winner will receive a £50.00 Claritystamp Voucher
You got to be in it to win it!
Looking forward to seeing all your lovely art work
For more information and to see the rules of the challenge click on the link below
All Groovi Items can be seen by clicking on the Orange Banner at the top right of this page where you will see all the Groovi on offer to date.